The Stair Landing Extension S allows to increase the surface in the direction of the primary beam, thus extending the length from 33 1/2 inch to 57 inch . The width is still the same as the size range of the Stair Landing S.
|Kind of product||Extensions kits|
|Maximum height above the flooring board (inch)||91 7/8|
|Minimum height above the flooring board (inch)||63 1/8|
|Height-adjustable every (inch)||4 3/4|
|Width/Lenght-adjustable every (inch)||3 7/8|
|Net weight (Lb)||36|
|Gross weight (Lb with packaging)||38|
|Load capacity in its minimum extension (lb/ft²)||41|
|Load capacity in its maximum extension (lb/ft²)||41|
|Beam height (inch)||3 7/8|
|Flooring material||European Radiata pine plywood 11/16 inch thick|
Tecrostar mezzanines and stairs are supplied with everything you need to install the kit at its maximum surface area or height.
Personalised phone or email service from our specialists
The stairs can be placed in different positions, increasing the possible configurations
Case 1: Exterior stairs, perpendicular to the mezzanine.
Case 2: Interior stairs. You will need a beam for interior stairs.
Case 3: Exterior stairs, parallel to the mezzanine. You will need a stair landing.
Case 4: A different placement to our mezzanines.
Yes, our products can be installed outdoors, although you should bear in mind a series of special considerations and carry out maintenance of the material to guarantee that they are in good condition. See this section for more details
Yes. They can be installed on a surface that is not a Tecrostar surface. The customer must bear in mind that they are responsible for the strength of the joint and structure to which they are anchored.
If you need to anchor the stairs to a structure that is not a Tecrostar structure, see the following details about the anchors:
References that have this anchor: 30501, 30401, 31003, 31301, 31102
Referencias que llevan este anclaje: 30303-0
References that have this anchor: 30601, 30801
Each model of stairs has an inclination and it cannot be changed unless otherwise stated. You must choose the stairs that best suit your needs.
To install Tecrostar mezzanines you need 2 adults (they do not need to be DIY experts). It is recommendable to use personal safety equipment like gloves, boots, etc. in order to avoid accident.
When installing range L mezzanines you may need to use some type of scaffolding or ladder for working at heights and manual or electric lifting machinery to raise the primary beams, particularly if the structure is more than 3m high. The other ranges can be lifted easily by hand.
You will need the following tools to install the mezzanines: tape measure, some type of spanner for m10 and m8 bolts and a screwdriver (an electric screwdriver will make the task much easier), spirit level, drill and a tool for cutting the panels (saw, jigsaw, circular saw, etc.)
You can find all the tools required to assemble it and tested by Tecrostar in the tools section.
All the models are installed by following these steps:
Pre-assemble the structure on the floor in the desired area.
Raise the outer structure to the desired height.
Finish assembling the structure and floor.
You can do it yourself with the help of a friend. It is easily installed in a few hours, depending on the product.
TS8 Mezzanine: 3 hours with 2 people
TM15 Mezzanine: 4 hours with 2 people
TL30 Mezzanine: 5 hours with 3 people
The times are a guideline and for assembly only. You need to add the time it takes to measure up, move the components to the location, clean up, etc.
For products in stock (white and black for S, M and L ranges), the delivery time will be approximately 5 working days from placing the order. Once the product has left our facilities, the normal transport time is between 7 and 10 working days. The transport time varies greatly and is difficult to control due to many factors: Place of delivery, local holidays, customs, etc.
If we cannot meet this delivery time, we will contact you.
Mezzanines are shipped in boxes by an external company in a lorry with a tail lift that enables the box to be unloaded to the ground (at street level at the customer’s address).
Don't be alarmed by the total weight of the product, the components are light and manageable, so you can move them easily and take them up in the lift. The heaviest components are the primary beams from the L range (39 kg), the rest of the ranges are considerably lighter (12kg). The floor panels are very light and fit in any lift. No component is more than 2.4m long and therefore, fits in most lifts.
In most cases, you can.
Tablas comparativas de escaleras
Tecrostar products are manufactured with the most suitable materials for the proposed technical solutions, combining wood, steel and top quality aluminium.
TECRO has earned certification from the AEM, the federation of Spanish materials handling. We have also received a Gold Medal Award of Merit from the INPEX (Invention and New Product Exposition), the top award for innovation at the largest Invention Exposition in the USA.