Full metallic mezzanine and wooden floor kit, with no need of works. With its easy and safe assembly, it is ideal to be installed in small spaces dividing any room into two: bedrooms, offices, storage, etc.
The kit includes everything you need to assemble your own tailored metal mezzanine without any work:
If you want to install the ladder inside the mezzanine, it is necessary to acquire the Beam for interior stairs S kit.
The TS 8 Mezzanine is a complete metal mezzanine designed to make the most of small spaces. Robust and easy to install without works or bricklaying, it is the ideal mezzanine for dividing rooms with high ceilings. It bears 41 lb/ft² when it is totally extended, that is to say, 3,087 lb weight uniformly distributed all over the surface. Therefore, you could set up an entire bedroom or a workspace, turning the room into two in total safety.
The Mezzanine TS8 consists of an adjustable metallic mezzanine for any size, extensible from 32 ft² to 86.11ft².
|Kind of product||Full Kits|
|Maximum height above the flooring board (inch)||91 7/8|
|Minimum height above the flooring board (inch)||63 1/8|
|Height above the beam (inch)||62 1/4, 67 1/2, 72, 76 3/4, 81 1/2, 86 1/4, 91 1/4|
|Beam height (inch)||3 7/8|
|Height-adjustable every (inch)||4 3/4|
|Width/Lenght-adjustable every (inch)||3 7/8|
|Maximum length of the secondary beam (inch)||101 1/8|
|Minimum length of the secondary beam (inch)||57 7/8, 57 7/8|
|Maximum length of the primary beam (inch)||101 1/8|
|Minimum length of the primary beam (inch)||61|
|Maximum area (ft²)||86.11|
|Minimum area (ft²)||32.29|
|Total maximum load (Lb)||3,086|
|Load capacity in its minimum extension (lb/ft²)||143|
|Load capacity in its maximum extension (lb/ft²)||41|
|Incline and shadow||80º / The shadow of the stairs is 17% of the height.|
|Kind of stairs||Ladder|
|Material and finish of the structure||Structural steel painted with powder coating|
|Material and finish of the handrails||Aluminiun, Anodized painting / Black lacquered / Wood effect|
|Material and finish of the posts||Steel painted with powder coating|
|Flooring material||European Radiata pine plywood 11/16 inch thick|
|Net weight (Lb)||485|
|Gross weight (Lb with packaging)||556|
Tecrostar mezzanines and stairs are supplied with everything you need to install the kit at its maximum surface area or height.
Personalised phone or email service from our specialists
The metallic Tecrostar mezzanines of the S, M and L ranges support a uniformly distributed load of 40,96 lb/ft² (that means that you can place a 40,96 lb distributed load on each square ft). This is the live load for residential uses according to the international regulations. The total maximum load will be 40,96 lb by the ft² of the mezzanine.
The steel pieces such as structures, railing posts and the stringers of the stairs are available in:
Black and white. Available in stock without additional costs.
Any RAL monolayer colour. With extra cost and upon request. Consult delivery time.
In both cases the paint is a lacquer with maximum adhesion applied by electrostatic process with polyester powder paint, suitable for outdoors.
Yes, it does. They are structural boards made by european radiata pine plywood 18mm thick. They have tongue-and-groove joints in their four sides.
Length: 81 7/8"
The kit includes as many boards as needed to install the mezzanine in its maximum dimensions. To install the mezzanine in smaller dimensions, it is necessary to cut the boards as it is explained in the installation manual included in the mezzanine kit. Cutting the boards is really easy and all the required tools are available at our online store as well.
No. Tecrostar has not a different flooring alternative. However, it is possible to personalize the finish of the floor adding some accessories on the boards (carpet, platform,...). Check our floor finishes in accessories section. If the customer installs a different floor from the boards provided, it is their responsibility to ensure the resistance of the full mezzanine, since the floor contributes to the stability of the whole.
No, you can’t. At the moment, our mezzanines are available just for a single height although some customers install them on another existing mezzanine. In that case, the resistance of the existing one should be checked.
It depends on the beam type, we need to calculate the corresponding surface load. For example, a secondary beam TM 15 supports around 1234 lb. You should take into account that if we apply additional loads, a part of the bearing capacity of the beam is being consumed.
Should you have any doubt about important additional loads, contact our technical department.
Tecrostar products can be installed outdoors (exposed to the elements), provided that a series of special measures are taken during installation and that you carry out regular maintenance in order to ensure that the materials are in good condition. The recommendations are the following:
No, our mezzanines are sold with columns by default. We cannot guarantee the resistance of walls or corbels and the customer will be responsible if the product is modified in these cases.
Yes. Provided that the inclination is small, we can use a wedge under the mezzanine columns to level it. If the inclination is too small it might be not necessary at all and the slope might be imperceptible
You can adjust the structural floor, working around architectural barriers or irregular surfaces.
When the walls are irregular or when you want to work around a fixed object, the decking can be finished off against the wall
Adjustment from below:
Adjustment from above:
It is possible it to be lower it requires to cut the columns and drill again though. On the contrary, it is not possible it to be higher. The cut of the columns can be made by the customer or order Tecrostar to do it.
Yes. This is quite common and the results are very good. The telescopic system of the columns enables the height to be adjusted every 4 3/4", so in the worst case scenario you will have a 2 3/8" difference.
Yes, you can. However, the maximum load capacity will be unaffected.
You can choose between several types of stairs:
Alternating tread stairs
To install Tecrostar mezzanines you need 2 adults (they do not need to be DIY experts). It is recommendable to use personal safety equipment like gloves, boots, etc. in order to avoid accident.
When installing range L mezzanines you may need to use some type of scaffolding or ladder for working at heights and manual or electric lifting machinery to raise the primary beams, particularly if the structure is more than 3m high. The other ranges can be lifted easily by hand.
You will need the following tools to install the mezzanines: tape measure, some type of spanner for m10 and m8 bolts and a screwdriver (an electric screwdriver will make the task much easier), spirit level, drill and a tool for cutting the panels (saw, jigsaw, circular saw, etc.)
You can find all the tools required to assemble it and tested by Tecrostar in the tools section.
All the models are installed by following these steps:
Pre-assemble the structure on the floor in the desired area.
Raise the outer structure to the desired height.
Finish assembling the structure and floor.
You can do it yourself with the help of a friend. It is easily installed in a few hours, depending on the product.
TS8 Mezzanine: 3 hours with 2 people
TM15 Mezzanine: 4 hours with 2 people
TL30 Mezzanine: 5 hours with 3 people
The times are a guideline and for assembly only. You need to add the time it takes to measure up, move the components to the location, clean up, etc.
For products in stock (white and black for S, M and L ranges), the delivery time will be approximately 5 working days from placing the order. Once the product has left our facilities, the normal transport time is between 6 and 8 weeks. The transport time varies greatly and is difficult to control due to many factors: Place of delivery, local holidays, customs, etc.
If we cannot meet this delivery time, we will contact you.
Mezzanines are shipped in boxes by an external company in a lorry with a tail lift that enables the box to be unloaded to the ground (at street level at the customer’s address).
Depending on your order you can receive different packages: One box for the mezzanines of the S and M ranges or two boxes for L mezzanines.
Height: 21 1/4"
The stairs can share the box with the mezzanines if the are purchased at the same time or you can have a separate box for the stairs. Check the stairs section.
Don't be alarmed by the total weight of the product, the components are light and manageable, so you can move them easily and take them up in the lift. The heaviest components are the primary beams from the L range (86 lb), the rest of the ranges are considerably lighter (26.5 lb). The floor panels are very light and fit in any lift. No component is more than 94 1/2" long and therefore, fits in most lifts.
Sometimes, the carrier cannot access to point of delivery due to an extremely narrow street or any other difficulty. In such cases, the carrier cannot do the delivery with the usual truck and he may need to use a different vehicle or extra support. If the carrier considers that the point of delivery is complicated, request a quotation. If you don’t inform in advance that the access is complicated, the delivery will be paralysed until you pay the extra cost.
Tecrostar products are manufactured with the most suitable materials for the proposed technical solutions, combining wood, steel and top quality aluminium.
TECRO has earned certification from the AEM, the federation of Spanish materials handling. We have also received a Gold Medal Award of Merit from the INPEX (Invention and New Product Exposition), the top award for innovation at the largest Invention Exposition in the USA.