'The biggest mezzanine', that's how TL 35 is defined. This is the Tecrostar product that can develop more surface: 377 ft². This metallic mezzanine and wooden floors, but could also be used in homes. The TL 35 can be adjusted in all three dimensions (length, height and width). Like the other types of mezzanine, the structure TL 35 permits various combinations of stairs and accessories.
Load capacity from 41 lb/ft2 considering the maximum dimensions of the mezzanine. Reducing the measurements of the mezzanine, the load capacity increases. Not suitable for pallet-truck circulation due to the point load they trans.
TL 35 Structure consists on a light width and length adjustable frame, four extending telescopic pillars to change the height and a high density structural board floor. This one has horizontal siding so that get a quick installation and avoid unnecessary cuts.
The mezzanine is available in white and black, suitable for outdoor, also there are a wide variety of colors, on request and a small extra cost. All metal components are subjected to a quality painting process through a powder coating system.
Quality is one of the premises for Tecrostar, therefore the mezzanine TL 35 is designed according to the Eurocodes, following European safety standards more stringent.
Produt includes every needed component:
1.- Telescopic circular columns, telescopic beams, and connectors for junctions, made of structural steel (qualities: S275, S355). Cut by laser process, without any sharp edge. Materials are lacquered by powdered paint.
2.- Structural floor, high density waterproof interlocked wooden boards: 18mm thick.
3.- Fasteners (8.8 quality) and embellishments (tube caps, screw caps...)
4.- User manual.
*To install the stairs inside the structure, it is needed the beam for interior stairs.
|Kind of product||Only Mezzanine|
|Maximum height above the flooring board (inch)||134 7/8|
|Minimum height above the flooring board (inch)||82 1/4|
|Height-adjustable every (inch)||4 3/4|
|Width/Lenght-adjustable every (inch)||3 7/8|
|Net weight (Lb)||2350.1|
|Gross weight (Lb with packaging)||2495.6|
|Which height above the flooring board is needed?||From 111 to 135, From 91 3/4 to 111, From 82 1/4 to 91 3/4|
|Maximum width (inch)||211 3/8|
|Minimum width (inch)||140 1/2|
|Maximum length (inch)||250|
|Minimum length (inch)||175 1/4|
|Maximum area (ft²)||365.97|
|Minimum area (ft²)||150.69|
|Total maximum load (Lb)||14,991|
|Load capacity in its minimum extension (lb/ft²)||123|
|Load capacity in its maximum extension (lb/ft²)||41|
|Beam height (inch)||11 3/4|
|Flooring material||European Radiata pine plywood 11/16 inch thick|
Tecrostar mezzanines and stairs are supplied with everything you need to install the kit at its maximum surface area or height.
Personalised phone or email service from our specialists
Tecrostar products can be installed outdoors (exposed to the elements), provided that a series of special measures are taken during installation and that you carry out regular maintenance in order to ensure that the materials are in good condition. The recommendations are the following:
No, our mezzanines are sold with columns by default. We cannot guarantee the resistance of walls or corbels and the customer will be responsible if the product is modified in these cases.
You can adjust the structural floor, working around architectural barriers or irregular surfaces.
When the walls are irregular or when you want to work around a fixed object, the decking can be finished off against the wall
Adjustment from below:
Adjustment from above:
Yes. This is quite common and the results are very good. The telescopic system of the columns enables the height to be adjusted every 12 cm, so in the worst case scenario you will have a 6cm difference.
To install Tecrostar mezzanines you need 2 adults (they do not need to be DIY experts). It is recommendable to use personal safety equipment like gloves, boots, etc. in order to avoid accident.
When installing range L mezzanines you may need to use some type of scaffolding or ladder for working at heights and manual or electric lifting machinery to raise the primary beams, particularly if the structure is more than 3m high. The other ranges can be lifted easily by hand.
You will need the following tools to install the mezzanines: tape measure, some type of spanner for m10 and m8 bolts and a screwdriver (an electric screwdriver will make the task much easier), spirit level, drill and a tool for cutting the panels (saw, jigsaw, circular saw, etc.)
You can find all the tools required to assemble it and tested by Tecrostar in the tools section.
All the models are installed by following these steps:
Pre-assemble the structure on the floor in the desired area.
Raise the outer structure to the desired height.
Finish assembling the structure and floor.
You can do it yourself with the help of a friend. It is easily installed in a few hours, depending on the product.
TS8 Mezzanine: 3 hours with 2 people
TM15 Mezzanine: 4 hours with 2 people
TL30 Mezzanine: 5 hours with 3 people
The times are a guideline and for assembly only. You need to add the time it takes to measure up, move the components to the location, clean up, etc.
For products in stock (white and black for S, M and L ranges), the delivery time will be approximately 5 working days from placing the order. Once the product has left our facilities, the normal transport time is between 7 and 10 working days. The transport time varies greatly and is difficult to control due to many factors: Place of delivery, local holidays, customs, etc.
If we cannot meet this delivery time, we will contact you.
Mezzanines are shipped in boxes by an external company in a lorry with a tail lift that enables the box to be unloaded to the ground (at street level at the customer’s address).
Don't be alarmed by the total weight of the product, the components are light and manageable, so you can move them easily and take them up in the lift. The heaviest components are the primary beams from the L range (39 kg), the rest of the ranges are considerably lighter (12kg). The floor panels are very light and fit in any lift. No component is more than 2.4m long and therefore, fits in most lifts.
In most cases, you can.
Sometimes, the carrier cannot access to point of delivery due to an extremely narrow street or any other difficulty. In such cases, the carrier cannot do the delivery with the usual truck and he may need to use a different vehicle or extra support. If the carrier considers that the point of delivery is complicated, request a quotation. If you don’t inform in advance that the access is complicated, the delivery will be paralysed until you pay the extra cost.
Tecrostar products are manufactured with the most suitable materials for the proposed technical solutions, combining wood, steel and top quality aluminium.
TECRO has earned certification from the AEM, the federation of Spanish materials handling. We have also received a Gold Medal Award of Merit from the INPEX (Invention and New Product Exposition), the top award for innovation at the largest Invention Exposition in the USA.